ADTR1107ACCZ-R7

Mfr. #:
ADTR1107ACCZ-R7
Mfr.:
Analog Devices
Product Type:
RF Front-End IC
Series:
ADTR1107
Package / Case:
24-LGA
Description:
6–18 GHz RF front end with PA, LNA and SPDT switch, 24-LGA

Product Attributes

AttributeValue
Frequency Range6–18 GHz
IntegrationPower amplifier, low-noise amplifier, reflective SPDT switch and directional coupler
Transmit Gain21.5 dB typical at 6–14 GHz, 22 dB typical at 14–18 GHz, VDD_PA = 5 V, IDQ_PA = 220 mA, TA = 25 °C, receive path off
Transmit Saturated Output Power25 dBm typical at 6–14 GHz, 24 dBm typical at 14–18 GHz, VDD_PA = 5 V, IDQ_PA = 220 mA, TA = 25 °C, receive path off
Transmit Output P1dB23 dBm typical at 6–14 GHz, 21.5 dBm typical at 14–18 GHz, VDD_PA = 5 V, IDQ_PA = 220 mA, TA = 25 °C, receive path off
Receive Gain17.5 dB typical at 6–14 GHz, 18 dB typical at 14–18 GHz, self biased at VDD_LNA = 3.3 V, TA = 25 °C, transmit path off
Receive Noise Figure2.5 dB typical at 6–14 GHz, 3 dB typical at 14–18 GHz, self biased at VDD_LNA = 3.3 V, TA = 25 °C, transmit path off
RF Impedance50 Ω internally matched I/O
PA Supply Voltage3.3–5.5 V, 5 V nominal
LNA Supply Voltage2.0–3.6 V, 3.3 V nominal
Switch BiasVDD_SW = +3.3 V and VSS_SW = −3.3 V
Control InterfaceCMOS/LVTTL CTRL_SW, low selects transmit and high selects receive
Quiescent CurrentPA 220 mA typical at VDD_PA = 5 V with gate bias adjusted, LNA 80 mA typical at VDD_LNA = 3.3 V with VGG_LNA = 0 V
RF Settling Time17 ns typical to within 0.1 dB of final RF output from 50% CTRL_SW, nominal bias at TA = 25 °C
Operating Temperature−40 °C to +85 °C
Package DetailsCC-24-8, 5 × 5 × 1.13 mm, exposed pad

Product Details

ADTR1107ACCZ-R7 combines a power amplifier, low-noise amplifier and reflective SPDT switch for a 6–18 GHz transmit/receive front end. A single control input selects the transmit-input-to-antenna path or the antenna-to-receive-output path, supporting a shared antenna connection in phased-array and radar systems. Internally matched 50 Ω RF ports simplify the RF interface.

The amplifiers have separate drain and gate bias connections. The PA gate voltage sets its quiescent current, while grounding VGG_LNA selects self-biased LNA operation. The switch also requires positive and negative 3.3 V rails. The board must implement the recommended bias sequence, including establishing the PA gate bias before its drain supply and applying the RF input after bias setup.

The coupled transmit output can feed an external power detector for transmit-level monitoring. Its coupling changes with frequency, so detector calibration must account for the operating band. Transmit compression and receive noise figure also vary between the specified sub-bands, making the intended frequency and bias point part of the RF link budget.

Quality · Shipping · Payment

Details

Quality Confirmation

Pre-shipment checks cover batch, package, labels and markings. Inspection photos and third-party inspection support are available on request.

Shipping

Worldwide delivery is supported. Carrier, lead time and buyer-appointed forwarder requirements are confirmed with the quotation.

Payment

Payment method, currency and trade terms are subject to the formal quotation or proforma invoice.